May 17, 2019 · # ip link add name gre1 type gre local LOCAL_IPv4_ADDR remote REMOTE_IPv4_ADDR [seq] key KEY While GRE tunnels operate at OSI Layer 3, GRETAP works at OSI Layer 2, which means there is an Ethernet header in the inner header. Here is how to create a GRETAP tunnel: # ip link add name gretap1 type gretap local LOCAL_IPv4_ADDR remote REMOTE_IPv4_ADDR

# ip a add 10.0.7.0/24 dev enp0s3 # ip a 2: enp0s3: mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 08:00:27:38:8f:84 brd ff:ff:ff:ff:ff:ff inet 192.168.0.113/24 brd 192.168.0.255 scope global dynamic enp0s3 valid_lft 2239sec preferred_lft 2239sec inet 10.0.7.0/24 scope global enp0s3 valid_lft Gateway IP Address: Enter the IP address of the gateway. The gateway is an immediate neighbor of your ADSL Router that will forward the packets to the destination. On the LAN, the gateway must be a router on the same segment as your Router; over Internet (WAN), the gateway must be the IP address of one of the remote nodes. Apr 18, 2019 · The next screen will give you an “IP logger link for collecting statistics” and “link for viewing statistics.” Copy the “viewing statistics” link to a safe spot. This is what you’ll use to see the person’s IP address and location afterward. The link for “collecting statistics” is the one with IP tracking in it. $ sudo ip link add eth10 type dummy NOTE: In older versions of ip you'd do the above like this, appears to have changed along the way. Keeping this here for reference purposes, but based on feedback via comments, the above works now. $ sudo ip link set name eth10 dev dummy0 And confirm it:

TP-Link Item model number TL-PA4010KIT Operating System Windows 10/8.1/8/7/Vista/XP/2000, Mac, Linux Item Weight 13.6 ounces Product Dimensions 2 x 2.6 x 1.1 inches Item Dimensions L x W x H 2 x 2.6 x 1.1 inches Color White Manufacturer TP-Link IP Cams Language: English ASIN B00AWRUICG Is Discontinued By Manufacturer No Date First Available

To create an 802.1Q VLAN interface on Ethernet interface eth0, with name VLAN8 and ID 8, issue a command as root as follows: ~]# ip link add link eth0 name eth0.8 type vlan id 8 To add a macvlan link, you can use: ip link add link eth0 type macvlan The interface will be named macvlanX where X is the first number such as no interface by that name exists. You can name the interface (to vif0 for example) at creation using something like. ip link add name vif0 link eth0 type macvlan to have an interface named vif0.

Dec 19, 2018 · # ip route add 192.168.2.0/24 via 192.168.2.254 dev eth0. Set a default route. All network packets that cannot be sent according to the previous entries of the routing table are sent through the following default gateway: # ip route add default via 192.168.1.254. Delete route from table. Type the following command # ip route delete 192.168.1.0

May 21, 2020 · A customer who is part of the Microsoft Certification program, and who holds an active certification(s), must perform specific steps to link or unlink their Microsoft Certification profile ID (MCID) with a Microsoft Partner Network (MPN) organization. This is necessary because of Personally Identifiable Information (PII) policies. Network interfaces can be enabled / disabled using ip link set interface up|down, see ip-link(8). To check the status of the interface eth0: $ ip link show dev eth0 2: eth0: mtu 1500 qdisc pfifo_fast master br0 state DOWN mode DEFAULT qlen 1000 May 17, 2019 · # ip link add name gre1 type gre local LOCAL_IPv4_ADDR remote REMOTE_IPv4_ADDR [seq] key KEY While GRE tunnels operate at OSI Layer 3, GRETAP works at OSI Layer 2, which means there is an Ethernet header in the inner header. Here is how to create a GRETAP tunnel: # ip link add name gretap1 type gretap local LOCAL_IPv4_ADDR remote REMOTE_IPv4_ADDR